Opinions questions about the use of Reinforced Concrete Design

Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions ideCAD can solve and equip these flooring systems and take their drawings and quantities. This type of flooring is called cork flooring or beamless flooring. There is a sample project in the link below.
You do not have permission to view link Log in or register now.
You can also refer to the links below regarding beamless flooring.
You do not have permission to view link Log in or register now.
You do not have permission to view link Log in or register now.
You do not have permission to view link Log in or register now.
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions Hello, while getting column application drawings; The basement curtains, the offset of which is designed according to the outer surface of the columns, give drawings with a different offset than the design.
 
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions Hello, if you define the joint points of the curtains as being at the column joint point, there will be no problem if you define them as offset. Check out the attached model.
 
Re: Opinions questions about using ideCAD Reinforced Concrete 8 I want to enter cork flooring in my attached project. Are my tile edge lines correct? In the trim edge edge curtains, I went from the beginning and end, or should I continue along the curtain edge?
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions SA... WE CAN'T JUST GET FRAME RESULTS AS REPORTS. THERE WAS SOMETHING LIKE THIS IN OLD VERSIONS. I CANNOT FIND IT IN THE IDE8. IT IS NOT POSSIBLE TO ANALYZE WITH A MATERIAL OTHER THAN CONCRETE OR STEEL (eg WOOD) AND GET THE REPORT. A REPORT LIKE THAT IN GENERAL ANALYSIS PROGRAMS WOULD BE SUPER...
 
Re: Opinions and questions about using ideCAD Reinforced Concrete 8 My computer has 32 bit 7.022 version installed, I could not install 8.103 or 8.5 version, I wonder if it supports :(
 
Re: Opinions questions about using ideCAD Reinforced Concrete 8 You must use a 64 bit operating system for V8.x.
 
Re: Opinions and questions about using ideCAD Reinforced Concrete 8 Hello. As can be seen in the picture, the objects disappear meaninglessly in the perspective view section of the image configuration. I have not been able to figure out the reason. I think that my computer is insufficient in terms of hardware (laptop with i5 3gb ram ati radeon hd 5470 video card). Or did I change a setting without realizing it? I will be glad if you help. good work.
 
Re: Opinions and questions about using ideCAD Reinforced Concrete 8 Hello Mr. dotcomtr I had a similar problem. I shared it here. Update your video card driver. If it doesn't resolve, get a CAPACITY computer like me. Unver ÖZCAN
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
"unver":67e41tuh" said:
Hi Dear dotcomtr I had a similar problem. I shared it here. Update your video card driver. If it doesn't resolve, buy a CAPACITY computer like me Ünver ÖZCAN
Click to expand...
Hello Mr. Ünver ÖZCAN Thank you very much for your help I updated the graphics card (although it was difficult) the problem disappeared.Good work.
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
"unver":3t17jzxp" said:
Hi Dear dotcomtr I had a similar problem. I shared it here. Update your video card driver. If it doesn't resolve, buy a CAPACITY computer like me . Ünver ÖZCAN
Click to expand...
Hello, Mr. Ünver. What are your computer hardware specifications? My computer has Intel i5 6500 processor, 16GB RAM, SSD. There is no external graphics card. In large projects with semi-rigid diaphragm and large projects, stuttering occurs when viewing analysis results on the perspective screen. Single When you make the solid visible, there is relief. There is no slowdown when viewing the solid model. I think the internal graphics chip of the processor is not enough, I suspect this, so I would like to know your situation.
 
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions Hello, I just got the ideCAD 8.504 update. I will do a building analysis. I saw a network formation error in the semi-rigid solution by chance in the forum. Can you post a new broken link? Best regards.
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions Hello, If you add your project, we can look at the cause of the problem. If there is a situation caused by the version, we need to take it into our notes to fix it. You can download ideCAD Steel and Reinforced Concrete version 8.103 from the attached link.
You do not have permission to view link Log in or register now.
 
About Circular Foundation Hello Friends, I Want to Define a Circular Foundation in a Circular Building, But on the Foundation Floor, the Circular and Other Curvilinear Commands Are Not Active in the Static Floor Edge Command. Does anyone know the reason or have encountered it before. Good work...
 
Re: About Circular Foundation
"zalman":1cpzhawc" said:
Hi Friends, I Want to Define a Circular Foundation in a Circular Building, But on the Foundation Floor, the Circular and Other Curvilinear Commands Are Not Active in the Static Slab Edge Command. Does anyone know the reason for this? Or Encountered before. Good work...
Click to expand...
Hello, There is no possibility to draw a circular tile edge to define the raft basically. It can be defined as broken using the linear tile edge. The circle in 2D drawing tools can be used to help.
 
Re: About Circular Foundation
"YasinTezel":3klzlpa4" said:
"zalman":3klzlpa4" said:
Hi Friends, I Want to Define Circular Foundation in a Circular Building, But I Want to Define Circular Foundation in Static Slab Edge Command on Foundation Floor and Other Curvilinear Commands Are Not Active. Does Anyone Know The Reason Or Have Encountered It Before. Good work...
Click to expand...
Hi, there is no possibility to draw a circular tile edge to define the mat basically. It can be defined as a fracture using the linear tile edge. The circle in 2D drawing tools can be used to help.
Click to expand...
Thank you, good work...
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions HELLO EVERYONE... I HAVE A PROBLEM, SO THE TABLES ARE COMPLETELY EMPTY IN THE IDE REPORT SECTION. THE VERDANA TEXT HAS BEEN DELETED. I DOWNLOAD AGAIN, I UPLOAD AGAIN THE PROBLEM WAS FIXED THE FIRST TIME FOR THE WINDOWS FONT PAGE, BUT WHEN I GET THE SAME ERROR AGAIN, WHEN I WANT TO DOWNLOAD FONT AGAIN, IT INSTALLS THE FONT PAGE, BUT THE FONT DOES NOT APPEAR. I CHANGE THE FONTS IN THE IDECAD REPORT, BUT I CANNOT REGISTER FONT. WHEN I WANT TO RECEIVE A DIFFERENT REPORT, I HAVE TO CHANGE THE FONTS MANUALLY AGAIN. CAN WE CHOOSE FONTS IN THE IDECAD REPORT SECTION AT THE BEGINNING, AS A DIFFERENT CHARACTER INSTEAD OF DEFAULT VERDANA. BEST REGARDS...
 
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
"zalman":2ayrjmla" said:
HELLO EVERYONE... I HAVE A PROBLEM TELL ME THE TABLES ARE COMPLETELY EMPTY IN THE IDE REPORT SECTION. Loading I WINDOWS FONT PAGE IC the first time in the PRB has improved bUT AGAIN tHE SAME MISTAKE he bought me AGAIN FONT YUKLEME wanted to play my FONTANA Loading bUT FONT does not appear. I'm changing IDECAD REPORT on FONTANA, bUT FONT RECORD CAN nOT DIFFERENT BR REPORT BUY want me AGAIN FONT ELLE CHANGE I will NEEDED. IDECAD REPORT PART in the FONTS Initially SECEBILIYORMUYUZ HOWEVER, AS A DIFFERENT CHARACTER INSTEAD OF DEFAULT VERDANA REGARDS...
Click to expand...
Hello, if you call our Bursa office on Monday, we will connect to your computer via remote access and try to help you on the subject.
 
You must log in or register to reply here.
Back
Top