German 
French 
Spanish 
Portuguese 
Italian 
Arabic 
Russian 
Japanese 
Turkish You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Opinions questions about the use of Reinforced Concrete Design
- Thread starter Ismail Hakki Besler
- Start date
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions
RAdye If there is a foundation, the diameter of the reinforcement on the foundation is selected as 10. Therefore, it appears in the quantity or there is always the diameter of the basic stirrup Sent from my iPhone using Tapatalk"ofis2a":jpzx08ag" said:ideCAD 8 constantly shows the 10-gauge reinforcement for continuous foundations in the reports even though I did not mark it in the diameter selection. I was having this problem. Also, although it is not in any position in the detailed quantity, there is 10 reinforcement bars in the total quantity report. Additionally, if you add the favorites option in other dialogs regarding the reinforcement diameter selections, we can practically make the diameter selections. Good work...
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions While taking beam expansions and stair drawings, the scale is normally 25, but when I want to take them in a different scale, the size of the sheet changes but the drawings do not. Is there something I don't know?
HakanŞahin
Administrator
Re: Opinions and questions about using ideCAD Reinforced Concrete 8
Reinforcement selection is not made automatically in the dome. After analyzing the dome, click "Reinforced Concrete Design/Dome" and write the reinforcements until the missing As is corrected.After this stage, you can get the dome drawing."Dough":1vyi5e3k" said:When you want to take a dome drawing in the demo version, the program closes itself.Is there a solution?
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
Thank you."HakanŞahin":2kemracf" said:Reinforcement selection is not made automatically in the dome. After analyzing the dome, click "Reinforced Concrete Design/Dome" and write the reinforcements until the missing As is corrected. After this step, you can get the dome drawing."Hamur":2kemracf" said:The program closes itself when trying to get a dome drawing in the demo version. Is there a solution?
saridurmus
New Member
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions Dear Ofis2a, when you go to the static settings of the raft flooring, there are buttons to determine the coffee table size and how much it is per m2. You can edit it here.
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions Hello, in version 7, we could see the non-recovery parts of the foundation in the results section under the structure tree in the raft foundation soil tension control. I couldn't find this in version 8. Can you help? Thanks
Ismail Hakki Besler
Administrator
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
"ssesli":1rl95o68" said:Hi, we could see the unrecoverable parts of the foundation in the results section under the structure tree in the raft foundation soil tension control in version 7. I could not find this in version 8. .Can you help?
Levent Özpak
New Member
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions
Hello , Your statement has been included in our notes. Thank you. Good work"aykut_k":p9xo3tri" said:After installing version 8.103, when I take a section on the formwork plan of the hollow block system, it does not show the rib beams as in the attached. why?
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions Hi, When we select the reference beams in both directions in ide7 while creating a cassette slab, the slab is created, but unfortunately in ide8 it does not. Also, a reference cannot be shown on a beam outside the area where we will define the floor. This causes problems in defining the calculation beams in the same direction.
HakanŞahin
Administrator
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
There is no difference between 7 and 8 in the definition of cassette flooring. Could you add a sample project to create the situation you mentioned? I chose the following element step by step, as follows It will be very useful if you can write that I clicked."ssesli":112pp157" said:Hi, When we select reference beams in both directions in ide7 while creating a cassette slab, the slab was created, but unfortunately ide8 does not. reference cannot be shown on a beam outside the area. This causes problems in defining the calculation beams in the same direction.
Re: Opinions about the use of ideCAD Reinforced Concrete 8 questions I would also like to mention one more issue. ide7 found the midpoint of the rectangular route object we drew to create a staircase from each line. but iide8 finds it only on the first line of the object. In others, it does not hold from the middle point.
HakanŞahin
Administrator
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
This is a situation already found in our notes. Thanks for your report..."ssesli":3denfyk9" said:I would also like to point out one more thing. The middle point of the rectangular route object we drew to create the stairs was found in ide7 from every line, but ide8 also finds it only on the first line of the object. Others do not hold it from the middle point.
Re: Opinions about using ideCAD Reinforced Concrete 8 questions
It will be difficult to describe it this way. Do you mind if I connect with Teamviewer and show you live?"HakanŞahin":39iswl0i" said:There is no difference between 7 and 8 in cassette slab definition. Can you add a sample project where you can create the situation you are talking about? It would be very useful if you could write step by step that I chose this element, clicked it like this."ssesli":39iswl0i" said:Hi, When creating cassette slab, ide7 also selects the reference beams in both directions. It was being created, but unfortunately not in ide8. Also, reference cannot be made for a beam outside the area where we will define the slab. This causes problems in defining the calculation beams in the same direction.
Re: Opinions about using ideCAD Reinforced Concrete 8 questions Hi, Maybe it will be a lot, but when 1-architecture file is imported, the drawing does not place the drawing to the origin even if the origin move is clicked in the window that appears. Although the drawing was moved to exactly 0,0,0 coordinates before it was saved in Autocad. 2-When we close or open the layers, we have to zoom in or out to see the changes, otherwise you cannot see the changes.