Beam Slab Recovery Error in Project

M

metingon

New Member
Hello, I have a project and I can say that there is no one around me who knows much. I need your help urgently. Can you help me? I use İdecad 7, I drew with c30 concrete quality. At first, I made a slab calculation and when I made a slab analysis and looked at my slabs, it was purple. Then I saved the columns by increasing 10 cm. purple Then I do the analysis reinforced concrete and no one saves this time and the numbers are too low I can't save everything.
 
I really need a lot of help. I got bored 5 times. If you download the demo and look at the project, there is a situation. My pc is 64 bit Idecad 32 bit Acılıxor.
 
"metingon":9alw1j3d" said:
Hi, I have a project and I can say that there is no one around me who knows much. I need your help urgently. Can you help me? I use İdecad 7, I drew with c30 concrete quality. At first, I made a slab analysis and when I looked at my slabs, it was all purple, then the columns were 10 I saved it by increasing a cm. My beams have always saved it, but my floors are always purple Then I do analysis reinforced concrete and no one saves it this time and the numbers are too low, I can't save everything, I can't save any of them. It has a continuous basis and a singular basis. How can I do it? can anyone help me to fix it, where are my mistakes, what are my mistakes? I need to save
Click to expand...
Hello, There is a unit error in the slab loads. 0.45 tf/cm2 and 0.2 tf/cm2 are entered. There will be 0.45 tf/m2 and 0.2 tf/m2. It is recommended that you also consider the warnings in the geometry control.
 
what should i do, will it be fixed when i fix it, not only that, but at first i save the columns, then when i do analysis+reinforced concrete, all is gone. i will download the 64 bit demo version and what else am i going to do with it?
 
"metingon":1ikr3qr0" said:
what should I do, so when I fix it, will it be fixed not only that, but first I save the columns, then when I do analysis+reinforced concrete, all is gone. I'll download the 64 bit demo version and what else am I going to do with it? I like this
Click to expand...
Hello, you have entered the slab loads 10 000 times. If you take the loads normally, the results will return to normal. There is no issue with using a 32-bit or 64-bit demo..
 
"metingon":1gvxtrh2" said:
what should I do, so when I fix it, will it be fixed not only that, but first I save the columns, then when I do analysis+reinforced concrete, all is gone. I'll download the 64 bit demo version and what else am I going to do with it? i
Click to expand...
To fix this easily, change the unit of length to meters in the Design settings section of the Structure tree, then select the tiles and enter the slab loads correctly using the object properties command.
 
I saw 0.45 tf/m2 as 0.2tf/m2, I'm going to try now, what's wrong with the columns, can you help me with the project?
 
"metingon":3mnpv02l" said:
I saw 0.45 tf/m2 0.2tf/m2. It was added as a project file in my message Apart from this, since the system is a system with curtains, you need to enter the coefficient of R in the Analysis Settings of 7. (TDY 2007 Table 2.5) Since the openings are not large, you can get the floor thickness of 12 cm.
Click to expand...
 
"metingon":3qqbw5ex" said:
Unfortunately, I'm entering from the phone, if it's explained nicely in written
Click to expand...
From the Help menu of the program, click the Content line. In the dialog that opens, click the search line. In the Index tab, type Continuous basic or Singular basic as a keyword. Related topics will be listed at the bottom .
 
Sir, you looked at my project, how am I going to draw the foundation there, my columns are not in the same place, after all, I'm scratching on the singular basis, but how do I need to break on the singular basis?
 
"metingon":1zomzw9i" said:
Sir, you looked at my project, how will I draw the foundation there, my columns are not in the same place, after all, I'm scratching on the single basis, but how is the need to cross on the single basis
Click to expand...
From the Tools menu, click on the Architectural Plan/Pattern plan line. and single basic commands will be active. Then you can enter your permanent basics as explained in the help menu and the video linked. If you can't enter again, contact us by voice. Let's see what you can't. TEL: 0.224.220 67 17
 
In the video, the columns are not at the same level with me, but I am constantly asking whether I will add a crease between them on a fundamentally singular basis.
 
You must log in or register to reply here.
Back
Top